![]() You can use a paperclip to gently pry up the connection plate inside the thread and then screw on your charger or cartridge. Is the battery damaged Did you drop your battery on the ground or in water Unfortunately, it could be permanently damaged if the internal connections have been interfered with. We highly recommend using an external charger to charge all mods with external. It’s a super easy fix that just about anyone can do. Be careful Pushing too hard can cause further damage to the cartridge, so make sure you pay attention to what you're doing. The easiest way to fix this is just to replace the coil Vape is not charging. This connection plate is designed to move slightly in order to work with a variety of different vape cartridges with 510 thread. If your device isn’t firing, it might be because your battery isn’t sending power to your coil. This is the most common reason for a battery to stop working and it doesn’t mean that your battery, or your cartridge, is defective. You may even notice that the LED at the end of the battery is still turning on during a draw, showing that the battery is still activating, it’s just not transferring power back to the cartridge. This connection plate is what activates your vape cartridge and is also what allows your charger to transfer power back to your battery when charging. If you're still getting the error message and haven't tried a new coil yet, now is the time to do so to with a more extreme and irreversible fault with your battery/mod.If you are experiencing an issue where your vape pen battery won’t charge or hit with a cartridge screwed in, you may need to adjust the connection plate inside the 510 thread. Check these connection plates to make sure that when your battery is plugged in, it is actually charging. However, before you dispose of the device prematurely, there are some troubleshooting tips you might want to try. Bad Charger Connection It’s possible that your connection to the charger could also be an issue. ![]() You could be one of the unlucky users that end up with a disposable that just won’t hit or fire. If all is working properly again and you push the fire button for an extended period of time after installing a new coil, you can flame the new coil out and waste it. The most common issue is that the disposable stops firing (or hitting) or drastically loses performance. To see if the error message is present without having to refill the tank, turn the power down very low if possible, and push the fire button for a fraction of a second to see the message displayed. Re-assemble vaporizer and dry-fire before use. Use the cleaning swab to wipe the 510 threading of the vape body. Unthread and remove the coil from the vape body. Use the swab to wipe the inside of the coil chamber until clean. If that doesnt resolve the issue, the coil may need to be replaced as they. If you're still getting 'check atomizer' or 'no atomizer,' it's time to try another (new) coil if you have one on hand even an old or burned coil will suffice as long as the same error message appears. Use an alcohol filled cotton swab or lightly dip a dry cleaning swab in 91 isopropyl alcohol. If your coil wont heat up, first ensure it is properly attached to the battery. ![]() Your pin should sit in the center of the pen and spring up and down so it can connect with the clearomizer. Reinstall the coil and reassemble your tank until it's clean and dry. What if the Firing Pin is Blocking the Electric Current from My Vape’s Coils If you have just replaced your vape’s clearomizer and it isn’t creating vapor, then you may have displaced the firing pin during the installation process. You'll also need to clean the tank's interior, including the area where the coil rests. Usually this means the atomizer is either burnt out, the cartridge is bad, or the cartridge is not attached to the battery properly. When the tank is disassembled, unscrew the coil from the tank's base and clean the bottom of the coil where it screws into and makes contact with the tank. If your vape is blinking green but not working, the vape battery is dead and needs to be recharged, or its permanently destroyed. Atomizer Tank is not firing against the coil (Make Sure Atomizer Tank coil is touching your battery firing pen) A fairly common, frustrating problem with vape pens can be that your firing pin on the battery is not touching the metal part on the bottom of your atomizer, cartomizer, or clearomizer tank. You'll have to disassemble your tank as you would if you were replacing the coil, which, depending on the setup, may be uncomfortable and messy if you have a complete tank. When this oil gets in between the connection plates it reduces the conductivity, in other words, it can stop your battery from firing. Occasionally, this miraculously solves the problem. Remove and replace the coil in your tank. The first thing to do is wipe the threads of the battery and clearomizer/tank, reassemble and then try again.
0 Comments
Leave a Reply. |